Sub-Surface Lawn Drip Irrigation

Sub-Surface Lawn Drip Irrigation
How does sub surface drip irrigation work?

Drip irrigation works by delivering water slowly and directly to the roots of your turf via drip emitters. The high efficiency of drip irrigation results from two primary factors. The first is that the water soaks into the soil before it can evaporate or run off. The second is that the water is only applied where it is needed, rather than being subject to wind. 

Subsurface drip systems use an emitter line treated with herbicide to prevent roots from growing into the tubing (Techline AS XR) placed parallel to each other about half a foot below the soil. 

Drip line is best laid in a grid for lawns to allow uniformity of water coverage

What are the required components?

  • Backflow prevention kit - 
  • Tap timer
  • Arkal Filter
  • Pressure reducing valve
  • Air release valve
  • Low density poly pipe
  • Drip line
  • Wire pegs
  • Adaptors and fittings
  • Line flushing valve


 For more information on the description of each component, please click here.

Below is a typical set up including all the elements of drip and where they are to be installed.

Backflow Prevention Valve - Prevents back siphoning of non-potable water into the water supply and come in a range of varieties. All water authorities require back-flow prevention devices to be used on all fixed irrigation systems

Arkal Filter - You must use a filter. Drip emitters have very small openings that can become clogged. City water is not free from particles that will clog your drip emitters. For larger areas, use at least a 120 Mesh Disc Filter which should be installed after the backflow valve and before the pressure reduction valve.

Pressure Reducing Valve - If you are coming off a mains water supply you must use a Pressure Reduction Valve (PRV). Dripline is intentionally made from weak walled poly pipe so that is extremely flexible for ease of installation. A PRV must be installed to reduce the pressure inside the dripline. The PRV is installed after the filter and after the solenoid valves in an automatic system.

Air-Release Valves - Are essential protection for the system and should be installed at the highest point of the system. The purpose of the air release valve is to: 

  • allow air into the system once it is turned off;
  • prevent the drippers from sucking in air and possible soil particles when the system is turned off and the water in the system drains out through the lowest point.

Flush Valves - Should be installed at the lowest point of the system; this is to allow any rubbish that may have made its way into the system to prevent blocking the drippers. Its worth noting that the flush valve lets about 2L of water out each time the system turns on.

Wire Pegs - All of the different types of drip line should be staked at least every 2 meters. This is because the pipe will expand and contract with changing temperature which will push it up through the mulch if it is not staked down. 

 Before you get started there are a couple of things you need to do

  • Measure your water flow rate from the water source you will be using.
  • Draw a plan of the area you want to water to map out where your dripline will be placed.

For more information on flow rate and drawing plans please click here

How do I install it?

While drip systems are simple to design and install, there are some basic guidelines to follow that will assist your drip system to work efficiently.

The soil type dictates how far apart each run of Drip line should be installed and therefore how much Drip line is necessary for each site. If the spacing of the Drip line is wrong the system will not work efficiently. Once the correct spacing has been decided the meterage can either be paced out on site or if a scale drawing is available the meterage can be worked out very quickly from the square meterage of the gardens. It is crucial that you determine what type of soil you have before you decide which product is best for you. As an example the standard spacing for installation of Techline, Scapeline and Miniscape is 300mm, but:

  1. If the your garden beds are sandy the water will drain straight down and this will mean that you need to install the runs length of drip line closer together at around 150mm.
  2. If your gardens have high clay content the water will remain closer to the surface and the runs could be spaced out at 500mm.

Drip line is best installed in a grid pattern that includes a header and collector pipe in 19mm poly pipe. This will provide the most efficient system as well as providing the best locations to install air release and flush valves.

Related Products

drip filtersdripline accessoriesdriplinelow density pipe and fittingsIrrigation controllers


Previous Post Next Post

  • Admin SEO

Related products

Comments 0
Leave a comment
Your Name:*
Email Address:*
Message: *

Please note: comments must be approved before they are published.

* Required Fields

Your Cart: { cart.item_count } items

- +
You don't have any items in your cart.